BLACKFIRE GLASSPRO Coating System

Two parts for long-lasting ceramic glass coating!

BLACKFIRE GLASSPRO Coating System is a two-part product that is formulated to be a long-lasting ceramic glass coating. Only taking minutes to apply, BLACKFIRE GLASSPRO Coating System will protect your glass for up to one year. BLACKFIRE GLASSPRO Coating System creates a super hydrophobic surface, allowing for a clear line of vision.

As much as your eyes may be the window to the soul, your glass is very much so the window to the road. If you have a dirty windshield, you are asking for trouble. For safe driving, you need a clear line of vision, something you can only achieve with top-notch glass products.

BLACKFIRE GLASSPRO Coating System is a unique two-part ceramic glass coating system that allows for maximum effectiveness on your glass. Part I starts with basically applying a base layer. This layer will create cross-links that act like grappling points, allowing the product to fully bond to the glass surface. Next, when you apply Part II, this product will cling to the surface with its hydrophobic properties. Water and environmental contaminants will bead up and roll off more than ever before. This is because the BLACKFIRE GLASSPRO Coating System produces a low sliding angle that keeps these contaminants, such as, water, mud, sleet, and snow from sticking to the surface.

It is important to have clear glass to see through, so that you can drive more safely on the roads. To ensure this, it is critical that you follow all the steps to the BLACKFIRE GLASSPRO Coating System. First, it is recommended that you clean the glass with BLACKFIRE Glass Cleaner. Next, clay your glass with the BLACKFIRE Poly Clay and then polish the glass with BLACKFIRE Glass Water Spot Remover. These first three products together will completely rid your car of contaminants. Before you get to the BLACKFIRE GLASSPRO Coating System, prep the glass with BLACKFIRE Paint Prep to remove any lingering polishing oils and to get it ready for a properly bonded ceramic coating.

To apply BLACKFIRE GLASSPRO Coating System, you will work in two parts. First, saturate a foam applicator with Part I and apply it your glass surface in a crosshatch pattern. The product will flash (appear as a rainbow) within thirty seconds to one minute. Once that happens, you can now saturate a new foam applicator with Part II. Don’t wipe off Part I and instead, put Part II right on top and apply it to the surface in another crosshatch pattern. Finally, wipe any excess product away using a clean microfiber towel. No need to wait, your glass is good to go! Your glass will thank you for its new found clarity as the BLACKFIRE GLASSPRO Coating System will last you up to one year of hydrophobic greatness. It's best to apply Part II every three to four months for best results.

DIRECTIONS:

Ready the surface:
-First clean the surface to be coated with BLACKFIRE Glass Cleaner.
-It’s also recommended that the glass be clayed using BLACKFIRE Poly Clay and then polished with BLACKFIRE Glass Water Spot Remover. This fully removes all glass contamination.
-Then prepare the glass for coating with BLACKFIRE Paint Prep to remove any remaining polishing oils.
PRO TIP: If coating the windshield, it will be easier to work on one half of the glass at a time. If working on windows, you can do the whole surface at once.

Part I:
-Saturate a foam coating applicator with BLACKFIRE GLASSPRO Coating System Part I. -Wipe onto the surface using a crosshatch pattern -Immediately move on to the application of Part II - do not allow Part I to dry.

Part II:
-Saturate a new foam coating applicator with BLACKFIRE GLASSPRO Coating System Part II -Without wiping off Part I, apply to the surface using a crosshatch pattern over Part II. -Once complete, wipe excess product away using a clean microfiber buffing towel. -Important Info: Allowing Part I to dry before application of Part II may cause coating to fail. It's best to work on small sections of glass at a time to prevent this from occurring. -No curing time is necessary – your glass will be coated and ready to go immediately! -Reapply Part II every 3-4 months for best results. Both I & II are 30 ml.